Dash Cam Power Tap-In Loom for Range Rover Evoque 1 with EARLY overhead console (2011-14)

Power Tap-in Loom for Overhead
Console

for Range Rover Evoque with
EARLY console (2011 -14)

This listing is for a power tap-in loom for the Range
Rover Evoque (2011 -14).

IMPORTANT: This item in only suitable for the
early Range Rover Evoque with the EARLY type overhead console (see
photo) – the early type console was fitted from 2011 until around 2014.

This custom made loom simply plugs into the front
overhead console and gives you 3 power take off wires that you can use
to install an accessory of your choice, dashcam etc:

Ignition positive 12 Volts (Green
wire) – this comes live when you open the door and shuts off 10
minutes after locking the car ( can be used as ignition live ).

Permanent battery positive 12 volts (Yellow
wire) – this is permanently “battery” live and can be used for cameras
with parking mode

Earth (Black wire)

The beauty of this is there is absolutely no
cutting/splicing needed to your vehicles wiring which may void your
warranty.

This loom is ideal to wire in a dash-cam as it puts
power to where you’ll mount the camera without having to route any long
wires round the screen (plus you’d still need to find somewhere to take
power from).

Some dash-cams come with a cigarette lighter power
loom which are just unsightly and also runs the risk of having it
unplugged.

This kit also allows you to have a permanent and
ignition live feed so you can wire your camera to have parking mode
(where supported).

This is NOT �a
genuine Land Rover item.

We also sell this loom kitted with a USB module as
well as Nextbase and Garmin hardwire kits – see our other listings to
purchase.

Fitting details

IMPORTANT:

Ensure you wire your accessory to the loom before
fitting to the vehicle (to prevent accidental shorting when fitting)

Disconnect your battery -ve lead (in the engine
bay) before fitting the loom to the vehicle – this makes it less
likely for power surges that could damage car circuits when plugging /
unplugging the overhead console

Ensure there is fuse protection in any circuit you
add to the loom – we suggest a 2 Amp fuse

The power output from this loom is 12v many
dashcams use 5V USB power source – ensure you are connecting a device
/ circuit to this loom that uses 12v input (eg a 12v to 5V USB
converter)

Connecting any circuit to the battery live feed
could lead to a flat battery unless the attached circuit contains a
low voltage protection circuit that stops the power drain when the
voltage falls below 12v etc

The ignition live feed comes from the body control
module – if this is overloaded the circuit is isolated and can be
reset with an ignition cycle (turn the car on and off again)

The battery positive feed comes via fuse 27 (5 Amps)
�in the fusebox

Some badly designed electronic devices could
produce power spikes and electrical interference that could damage
circuits on the car or produce radio interference – we are not able to
test all devices so cannot accept any responsibility for any damage
from using this loom on your car but please report any issues us so we
can investigate and warn others.

If you have any issues with your car that needs
investigation by a Land Rover dealer it is best to disconnect this
loom so the vehicle is returned to its original configuration

If you are only using the ignition and earth wires
make sure that the battery positive wire is insulated so that it
cannot short to ground

See below video

Note: This listing is for the tap-in loom only
and does not include other items show in the video.

Range Rover Evoque Dashcam Install – YouTube

Video will open in a new window

[isdntekvideo]

Which Vehicles will this fit
?

This item WILL
fit the Range Rover Evoque 1st generation with the early type console
(from 2011 to around 2014)

This item WILL
NOT fit the
Range Rover Evoque 1st generation with the late type console (late type
console was used from around 2014 onwards)